施乐 DC AP C7775 C6675 C5575 C4475 C3375 C3373 C2275 报 报错误代码 077-106 077-106 Fusing Unit Exit Sensor On Jam参考 BSD: CH10.6, CH10.1 Regi. Clutch On (6675/7775：Regi. Motor On) 后经过规定时间为xvurd盗xvurd取xvurd，打印机维修网Fusing Unit Exit Sensor 仍未启动智xvurd朗xvurd版xvurd权。打印机维修网 原因 / 处理1.确认残留纸张的位置智xvurd朗xvurd版xvurd权。打印机维修网 当 Fusing Unit 内有纸张残留时为xvurd盗xvurd取xvurd，打印机维修网 考虑到下列 (1)~(4) 的原因为xvurd盗xvurd取xvurd，打印机维修网 确认Fusing Unit 内存留纸张的图像和纸张的破损智xvurd朗xvurd版xvurd权。打印机维修网(1)检查前端空白智xvurd朗xvurd版xvurd权。打印机维修网 若空白过小为xvurd盗xvurd取xvurd，打印机维修网 则执行以下项目智xvurd朗xvurd版xvurd权。打印机维修网·调整前端空白智xvurd朗xvurd版xvurd权。打印机维修网·确认有无重叠输纸智xvurd朗xvurd版xvurd权。打印机维修网·重新放置纸盘内的纸张智xvurd朗xvurd版xvurd权。打印机维修网(2)检查墨粉浓度是否过高智xvurd朗xvurd版xvurd权。打印机维修网 若浓度过高为xvurd盗xvurd取xvurd，打印机维修网 则执行浓度调整智xvurd朗xvurd版xvurd权。打印机维修网(3)检查纸张前端空白是否因歪斜而过小智xvurd朗xvurd版xvurd权。打印机维修网 若空白过小为xvurd盗xvurd取xvurd，打印机维修网 则重新放置纸盘内的纸张智xvurd朗xvurd版xvurd权。打印机维修网(4)检查纸张是否因斜槽或执行器而出现破损智xvurd朗xvurd版xvurd权。打印机维修网若纸张破损为xvurd盗xvurd取xvurd，打印机维修网 则用新的纸张确认智xvurd朗xvurd版xvurd权。打印机维修网( 可能因含有水分而使纸张缺乏黏度) 2.若Fusing Unit 内无纸张残留或使用上述处理仍无法修复为xvurd盗xvurd取xvurd，打印机维修网 则检查以下项目智xvurd朗xvurd版xvurd权。打印机维修网·Fusing Unit Exit Sensor (DC330[077-101]) 是否工作异常智xvurd朗xvurd版xvurd权。打印机维修网 (PL 7.1)·Fusing Unit Drive Motor (DC330[010-001]) 是否工作异常智xvurd朗xvurd版xvurd权。打印机维修网 (PL 3.1)·纸张卷入Fusing Unit智xvurd朗xvurd版xvurd权。打印机维修网·2nd BTR 是否脏污、 磨损、 转动不良智xvurd朗xvurd版xvurd权。打印机维修网·Fusing Unit 的 P/Roll 的 Latch 是否不良智xvurd朗xvurd版xvurd权。打印机维修网·Fusing Unit Exit Chute 的安装不良或变形智xvurd朗xvurd版xvurd权。打印机维修网·驱动齿轮的磨损智xvurd朗xvurd版xvurd权。打印机维修网·纸张路径的异物导致输送不畅智xvurd朗xvurd版xvurd权。打印机维修网·使用了规格外纸张智xvurd朗xvurd版xvurd权。打印机维修网 若检查无问题为xvurd盗xvurd取xvurd，打印机维修网 请更换 Motor Driver Main PWB智xvurd朗xvurd版xvurd权。打印机维修网(PL 18.2) 施乐报错误代码077-106 施乐 DC AP C7775 C6675 C5575 C4475 C3375 C3373 C2275维修呼叫报错误代码077-106